Voere Kufstein, 22lr , Self Loading Rifle

This paticular rifle (Mod2115) was made in 1973 according to date stamp on barrel and it has survived extremely well over the last 36 years
Voere cocking handle



Right hand view showing cocking handle and bolt lockback position for use in single shot mode,Locking back bolt helps in showing breach clear as well as making cleaning easier.

Voere Rear grip

Right hand side of rear grip showing lightly etched chequering.

Voere trigger and mag shot

Right hand side showing trigger,trigger guard/holding point for target shooting,15 round magazine

and magazine retaining/release clip.

Voere RH view

Slightly wider shot showing woodwork and chequering at both ends, also the safety catch is just visible

at rear of metalwork. Also shown is my 3-9×40 AO   Nikko-Stirling scope.

Made in Kufstein,Austria 1973


Voere 15 round mag

15 Round magazine with spring and tension button visible.

Voere magazine feed

Underside of rifle showing the magazine release and magazine insertion port.

Voere breach/chamber

Great shot of the breach/reciever where you can see the top of the magazine in place as well as the

barrel and the indent for extractor next to where the firing pin strikes onto the ‘rim’ of the cartridge.

Voere Safety catch

A good shot of the safety catch flip over lever currently in the ‘OFF’ position.

Voere sideshot

Just a right hand side shot where you can see the grooves on the cocking handle(sprung loaded)

Voere Rosewod(maybe?) end cap

Rosewood endcap.

Voere Butt pad

Buttpad looking a little bit worn but original.

Voere Foregrip

Foregrip chequering.


With the Parker-Hale moderator fitted- it makes for quite a long rifle but well balanced all the same.

Also visible are the Talon swivel studs I fitted as the originals were missing.


Easy to hold,bring up to the shoulder despite it’s length with the moderator, note the use of the grip in

front of the trigger. Not sure if this is supposed to be used as a palm rest/grip but it certainly serves the

purpose when target shooting enabling you to bring your elbow ‘in’ to support the shot being taken.
Well I have now had the stock redone by having it french polished and I must say it came back to me VERY nicely done, Take a look:-



16 Comments (+add yours?)

  1. patrick
    Jan 22, 2010 @ 19:50:00

    do you have a magasine for VOERE KUFSTEIN AUSTRIA CAL 22LR
    please sand me a email for a price i live in canada


    • jimandliz
      Jan 23, 2010 @ 05:43:11

      Sorry… didn’t ‘quite’ understand your comment??

      If you meant “do you have a magasine for VOERE KUFSTEIN AUSTRIA CAL 22LR” that YOU wish to buy from me then sorry, I only have the current one I’m using.

      They’re quite hard to find and even when found, they tend to cost a fair bit!!


      • owen
        Jan 19, 2012 @ 03:32:26

        .yes i have one my name is owen i was wondering if this rifel had any value?

      • jimandliz
        Jan 22, 2012 @ 05:19:45

        The rifle has never had high price but if you measure value in accuracy,reliability etc , then you’re onto a winner!!
        The Voere I have will ALWAYS be more accurate than I’ll ever be and as long as you feed it the correct ammo then it’ll be more accurate and reliable than many other higher priced semi out there 🙂

        Thanks for reading and replying ,



  2. rick donnelly
    Feb 20, 2010 @ 14:38:48

    Sir, can you please detail how this little rifle is stripped for cleaning, as I do not seem to be able to get this info on line except in German which I do not have.
    Many thanks for any time you spend on a reply.


    • jimandliz
      Feb 21, 2010 @ 03:43:03

      Certainly Rick,
      First remove the bolt underneath in front of the two which hold the trigger mechanism in place.
      Then lift out the WHOLE rifle with trigger mechanism still attached(usually easier to push out by pressure applied to underside of trigger guard whilst supporting the stock) . Next unscrew the safety catch housing by turning on the ‘grippy'(for want of a better word) part, don’t worry-it is under slight pressure from spring but nothing to be concerned with, just keep a firm hold of the housing and the rifle.
      You can then slide out/off the safety catch housing,bolt spring and the firing pin spring which goes inside the other spring.
      Slide the bolt back via cocking handle and then unscrew cocking handle by turning the screw inside the spring loaded cocking handle.
      Slide out the ‘bolt’ fully and remove via rear of rifle(you may need to ease it out with something non metal!!) inside that you will see the end of the firing pin which you can pull out and clean seperatly. You can also remove the loading tray just below the breach via the little screw on bottom of rifle.
      The trigger mechanism can also be removed via the two bolts but DO NOT strip the trigger action because it’s pretty much sealed but you CAN use an airline to blow out all the crap and then relube very lightly on all visible pivot points etc.
      You can also now clean the barrel from the breach end rather than the muzzle end which would/could affect the crowning of the muzzle!!

      Happy cleaning Rick


  3. Rick
    Apr 05, 2010 @ 13:55:11

    Dear ‘Jim’, Many thanks for you’re very detailed reply, I had actually forgotten I had written to you, hence the late reply, again, many thanks for the trouble taken.


  4. Catherine Côté
    Jun 23, 2010 @ 23:26:22

    Helo, the friend of my dad is shearching for a bolt action to arm the gun and the chargor. Iam french canadian I hope iam writing it those 2 thing corectly?! Do you know by any chance were he can order those two pieces ??? Thanks for your help I canot find anything else so far …


  5. Steve
    Sep 21, 2010 @ 02:41:41

    I am trying to find the whole bolt set for this gun (bolt, firing pin, safty switch) any idea where i could buy this stuff?


    • jimandliz
      Sep 22, 2010 @ 22:35:50

      Guntrader, I found two here . To be honest, I think it would work out just as cheap to buy a whole rifle as it would be trying to track down spare parts for the 1970’s rifle.


    • jimandliz
      Jan 12, 2011 @ 10:30:08

      You could try here


  6. beauregard
    May 19, 2012 @ 08:44:41

    Hi sir, i’m from France and I’m looking for a magazine for my rifle Voere Stlf1.
    Do you know how can I do to find one.


    • jimandliz
      May 21, 2012 @ 00:23:23

      You’ll need to browse through sites such as Gunstar and Guntrader or enquire at local gunsmiths/shops. I have never found a second magazine for mine , only complete rifles with magazine but even they’ve never been the 15 shot like I have now , more commonly 5 or sometimes 10 shot. Good luck.


  7. Czech
    Aug 02, 2012 @ 22:48:19

    Triple K Magazines now makes the magazine for both German and Austrian Voere 22’s. Kurt at Triple K ‘s Voere is a German 22 . Mine is an Austrian. Mag works in both.
    I need a recoil spring if anyone knows where parts are.



  8. j spence
    Oct 03, 2012 @ 00:27:38

    jim could you post a pic of the bolt with the extractor?
    i inherited the same gun and the extractor is missing,, my gunsmith said he could make one if he had a pic of the extractor
    thanks jason


    • jimandliz
      Oct 04, 2012 @ 22:06:21

      I can post a pic but I’m not sure if it will help much !! I’ll strip down to the bolt but I’m not going to remove the extractor from bolt as it looks a bit fiddly to get back in and I’m gonna need it Friday night for a Timed/rapid fire competetion (round 1) .


Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out /  Change )

Google+ photo

You are commenting using your Google+ account. Log Out /  Change )

Twitter picture

You are commenting using your Twitter account. Log Out /  Change )

Facebook photo

You are commenting using your Facebook account. Log Out /  Change )


Connecting to %s

%d bloggers like this: